Mam serię laptopów z dyskami Toshiby MK3256GSY. W podobnym czasie
większość (wszystkie?) dysków zaczyna się "kończyć", przy czym
większość ma realokowane sektory i raw_value 191 (G-Sense_Error_Rate)
na poziomie >3000 (value/worst/threshold 100/100/000).
Jeden nie ;), ma natomiast inne błędy, których do końca zinterpretować
nie potrafię.
Przede wszystkim atrybut 187 (Reported_Uncorrect) jest niebezpiecznie
blisko progu (001/000), gdy pozostałe dyski mają 100/000. (zastanawiam
się też czy ma szansę kiedykolwiek ten próg osiągnąć)
Podejrzewam też, że błędy widoczne w error logu (Error: UNC ...") są
właśnie z tym "uncorrect" związane. Ale co to za błędy?
Kolejną dziwną rzeczą jest temperatura. Wczoraj raw_value było 22/24,
później max nieco się podniósł w trakcie pracy. Dziś już minimum ma 41
stopni. Tak jakby jakoś resetował licznik po wyłączeniu komputera.
Długie testy S.M.A.R.T. wszystkie dyski przechodzą, atrybuty
(realokowane sektory i inne błędy) po teście nie zmieniają się.
A, pozostałe dyski (z realokowanymi sektorami) mają raw_value 183
(Runtime_Bad_Block) = 1, ten opisywany poniżej = 2.
Poniżej wyniki. Jakie są Wasze opinie na temat tego dysku?
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.1.0-3-grml-amd64] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA MK3256GSY
Serial Number: 60CBFC89S
LU WWN Device Id: 5 000039 296c83bd0
Firmware Version: LH013C
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Feb 27 09:32:48 2013 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x51) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 80) minutes.
SCT capabilities: (0x0033) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0007 100 100 050 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 100 100 002 Pre-fail Always - 2179
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 1946
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 1757
10 Spin_Retry_Count 0x0013 138 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1923
183 Runtime_Bad_Block 0x0022 100 100 001 Old_age Always - 2
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
185 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 65535
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 223
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 001 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 058 047 045 Old_age Always - 42 (Min/Max 41/42)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 115
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 524296
193 Load_Cycle_Count 0x0032 095 095 000 Old_age Always - 54850
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 236 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 236 occurred at disk power-on lifetime: 1168 hours (48 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 0a ac 30 4b 40 Error: UNC at LBA = 0x004b30ac = 4927660
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 80 08 88 30 4b 40 00 00:13:31.860 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 00:13:31.860 SET FEATURES [Enable write cache]
aa aa aa aa aa aa aa ff 00:13:31.840 [RESERVED]
60 80 08 88 30 4b 40 00 00:13:28.709 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 00:13:28.709 SET FEATURES [Enable write cache]
Error 235 occurred at disk power-on lifetime: 1168 hours (48 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 0a ac 30 4b 40 Error: UNC at LBA = 0x004b30ac = 4927660
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 80 08 88 30 4b 40 00 00:13:28.709 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 00:13:28.709 SET FEATURES [Enable write cache]
aa aa aa aa aa aa aa ff 00:13:28.690 [RESERVED]
60 80 08 88 30 4b 40 00 00:13:25.558 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 00:13:25.558 SET FEATURES [Enable write cache]
Error 234 occurred at disk power-on lifetime: 1168 hours (48 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 0a ac 30 4b 40 Error: UNC at LBA = 0x004b30ac = 4927660
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 80 08 88 30 4b 40 00 00:13:25.558 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 00:13:25.558 SET FEATURES [Enable write cache]
aa aa aa aa aa aa aa ff 00:13:25.540 [RESERVED]
60 80 08 88 30 4b 40 00 00:13:22.407 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 00:13:22.407 SET FEATURES [Enable write cache]
Error 233 occurred at disk power-on lifetime: 1168 hours (48 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 0a ac 30 4b 40 Error: UNC at LBA = 0x004b30ac = 4927660
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 80 08 88 30 4b 40 00 00:13:22.407 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 00:13:22.407 SET FEATURES [Enable write cache]
aa aa aa aa aa aa aa ff 00:13:22.390 [RESERVED]
60 80 08 88 30 4b 40 00 00:13:19.256 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 00:13:19.256 SET FEATURES [Enable write cache]
Error 232 occurred at disk power-on lifetime: 1168 hours (48 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 0a ac 30 4b 40 Error: UNC at LBA = 0x004b30ac = 4927660
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 80 08 88 30 4b 40 00 00:13:19.256 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 00:13:19.256 SET FEATURES [Enable write cache]
aa aa aa aa aa aa aa ff 00:13:19.239 [RESERVED]
60 80 08 88 30 4b 40 00 00:13:16.105 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 00:13:16.104 SET FEATURES [Enable write cache]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 1750 -
# 2 Extended offline Completed without error 00% 1618 -
# 3 Short offline Completed without error 00% 9 -
# 4 Short offline Completed without error 00% 9 -
# 5 Short offline Completed without error 00% 8 -
# 6 Short offline Completed without error 00% 8 -
# 7 Short offline Completed without error 00% 7 -
# 8 Short offline Completed without error 00% 3 -
# 9 Short offline Completed without error 00% 3 -
#10 Short offline Completed without error 00% 2 -
#11 Short offline Completed without error 00% 2 -
#12 Short offline Completed without error 00% 1 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
-- Jacek PolitowskiReceived on Wed 27 Feb 2013 - 10:30:02 MET
To archiwum zostało wygenerowane przez hypermail 2.2.0 : Wed 27 Feb 2013 - 10:51:04 MET