linux pld ac - 2.6.13.2 - dlugie

Witam

zakupilem nowy dysk twardy seagate barracuda 160GB zainstalowalem linuxa pld
ac z jadrem 2.6.8.costam. wszystko przez jakis czas bylo ok ale po pewnym
czasie caly system zaczal mi sie wieszac, w /var/log/messages byly jakies
bledy dotyczace DMA tego dysku. Nie pamietam ich za bardzo ale dane mi
zniknely wiec postanowilem oddac dysk na gwarancji. Dostalem taki sam nowy i
ponownie mam problemy:
objawy te same:
system sie w pewnym momencie zawiesza
i na poczatku zaczely sie pojawiac bledy:
hda: lost interrupt
sciagnalem sobie nowe jadro i wkompilowalem acpi, bledy na jakis czas zniknely
ale po jakims czasie pojawily sie nowe (hda: lost inerrupt zniknely).
po pewnym czasie zapuscilem na dluzszy czas zapis/odczyt z dysku ale wszystko
sie wysypalo wiec sprawdzilem badbloki i niestety pojawilo sie ich bardzo
duzo.

mam plyte glowna: via kt3 ultra2-c

czy ktos wie co z tym zrobic?

dolaczam kilka dodatkowych informacji:
dmesg:
Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
irda_init()
NET: Registered protocol family 23
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: dde00000-dfefffff
  PREFETCH window: cdb00000-ddcfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1128860537.880:1): initialized
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.23 [Flags: R/W DEBUG].
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: CPU0 (power states: C1[C1])
ACPI: Processor [CPU1] (supports 16 throttling states)
lp: driver loaded but no devices found
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
[drm] Initialized drm 1.0.0 20040925
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Via IRQ fixup for 0000:00:12.0, from 11 to 0
eth0: VIA Rhine II at 0x1d400, 00:10:dc:75:ea:4a, IRQ 16.
eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
eth1: RealTek RTL8139 at 0xf080ef00, 00:06:4f:00:79:24, IRQ 17
eth1: Identified 8139 chip type 'RTL-8139C'
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 15
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST3160812A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: LITE-ON DVDRW SOHW-1673S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA
(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.12 loaded.
mice: PS/2 mouse device common for all mice
oprofile: using NMI interrupt.
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
ip_conntrack version 2.1 (6143 buckets, 49144 max) - 212 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.
snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 UAR1 USB1 USB2 USB3 EHCI USB USBA USBB AC9 MC9 ILAN SLPB
ACPI: (supports S0 S1 S3 S4 S5)
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 168k freed
Adding 2048276k swap on /dev/hda2. Priority:-1 extents:1
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 2
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 18, io base 0x0000dc00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 2
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 18, io base 0x0000e000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 2
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#3)
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 18, io base 0x0000e400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
usb 1-2: reset full speed USB device using uhci_hcd and address 2
usbcore: registered new driver speedtch
speedtch 1-2:1.0: no stage 1 firmware found!
ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:10.3, from 5 to 2
ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 18, io mem 0xdffffe00
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
usb 1-2: USB disconnect, address 2
usb 1-2: new full speed USB device using uhci_hcd and address 3
usb 1-2: reset full speed USB device using uhci_hcd and address 3
usbcore: registered new driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.23:USB Abstract Control Model driver for USB
modems and ISDN adapters
speedtch 1-2:1.0: no stage 1 firmware found!
Linux video capture interface: v1.00
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 19
bttv0: Bt878 (rev 2) at 0000:00:07.0, irq: 19, latency: 32, mmio: 0xdddfe000
bttv0: detected: AVerMedia TVPhone98 [card=41], PCI subsystem ID is 1461:0001
bttv0: using: AVerMedia TVPhone [card=6,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=000477c3 [init]
bttv0: using tuner=-1
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips:
tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pi
c16c54
(PV951),ta8874z
bttv0: i2c: checking for TDA9887 @ 0x86... not found
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: add subdevice "remote0"
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
eth0: link down
eth1: link down
usbcore: deregistering driver speedtch
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
via82xx: Assuming DXS channels with 48k fixed sample rate.
         Please try dxs_support=5 option
         and report if it works on your machine.
         For more details, read ALSA-Configuration.txt.
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 20
PCI: Via IRQ fixup for 0000:00:11.5, from 10 to 4
PCI: Setting latency timer of device 0000:00:11.5 to 64
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110269
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110269
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110277
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110277
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110285
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110285
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110293
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110293
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110301
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110301
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110309
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110309
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110317
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110317
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110325
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110325
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110333
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110333
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110341
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110341
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110277
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110277
Buffer I/O error on device hda5, logical block 651713
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110285
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110285
Buffer I/O error on device hda5, logical block 651714
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110293
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110293
Buffer I/O error on device hda5, logical block 651715
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110301
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110301
Buffer I/O error on device hda5, logical block 651716
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110309
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110309
Buffer I/O error on device hda5, logical block 651717
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110317
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110317
Buffer I/O error on device hda5, logical block 651718
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110325
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110325
Buffer I/O error on device hda5, logical block 651719
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110333
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110333
Buffer I/O error on device hda5, logical block 651720
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110341
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110341
Buffer I/O error on device hda5, logical block 651721
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110341
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110341
Buffer I/O error on device hda5, logical block 651721
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110341
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110341
Buffer I/O error on device hda5, logical block 651721
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110341
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110341
Buffer I/O error on device hda5, logical block 651721
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=112110342, high=6,
low=11447046, sector=112110341
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 112110341
Buffer I/O error on device hda5, logical block 651721

hdparm:
/dev/hda:
 multcount = 16 (on)
 IO_support = 1 (32-bit)
 unmaskirq = 1 (on)
 using_dma = 1 (on)
 keepsettings = 0 (off)
 readonly = 0 (off)
 readahead = 256 (on)
 geometry = 19457/255/63, sectors = 312581808, start = 0

dodam ze czasami dzialo sie tak ze dysk na chwile sie zawieszal i po chwili w
logach ukazywala sie informacja, "disk ..... reset" i w hdparm pojawialo sie
cos takiego:
/dev/hda:
 multcount = 0 (off)
 IO_support = 0 (off)
 unmaskirq = 0 (off)
 using_dma = 1 (on)
 keepsettings = 0 (off)
 readonly = 0 (off)
 readahead = 256 (on)

hdparm przy starcie systemu jest ustawiany na:
-qm 16 -qa 256 -qc 1 -qu 1 -qd 1 -X66
dodam ze bez -X66 tez wszystko bylo zle.

z gory dzieki za odpowiedzi.

-- 
Wysłano z serwisu Usenet w portalu Gazeta.pl -> http://www.gazeta.pl/usenet/