Re: Problem z Epox 8RDA3

Użytkownik ike napisał:

> Użytkownik Andrea napisał:

Dolaczam jeszcze dane z Sandry

SiSoftware Sandra

Mainboard
Manufacturer : Pronix (Epox)
MP Support : No
Model : nVidia-nForce
System BIOS : 07/29/2004-nVidia-nForce-6A61BPAIC-00
Chipset : nVidia nForce2 ICP

System Memory Controller
Location : Mainboard
Error Correction Capability : None
Number of Memory Slots : 3
Maximum Installable Memory : 1.5GB
Bank0/1 - A0 : Empty
Bank2/3 - A1 : Empty
Bank4/5 - A2 : DIMM 512MB

Chipset 1
Model : Nvidia Corp nForce2 AGP Controller
Bus(es) : ISA AGP PCI USB i2c/SMBus
Front Side Bus Speed : 2x 167MHz (334MHz data rate)
Maximum FSB Speed / Max Memory Speed : 2x 200MHz / 2x 200MHz
Width : 64-bit
IO Queue Depth : 8 request(s)

Chipset 1 Hub Interface
Type : HyperTransport
Version : 0.10
In/Out Width : 8-bit / 8-bit
Speed : 2x 200MHz (400MHz data rate)

Logical/Chipset 1 Memory Banks
Bank 1 : 512MB DDR-SDRAM 2.5-3-3-8CL 2CMD
Channels : 1
Speed : 2x 200MHz (400MHz data rate)
Multiplier : 6/5x
Width : 64-bit
Power Save Mode : No
Fixed Hole Present : No

Memory Module(s)
Memory Module 3 : TwinMOS M2G9JA8AMK9F081CAD 5E401D93 512MB 16x(32Mx8)
DDR-SDRAM PC3200U-2533-600 (CL2.5 up to 200MHz)

Environment Monitor 1
Model : Winbond W83627(T)HF ISA
Version : 2.01
Mainboard Specific Support : No

Temperature Sensor(s)
Board Temperature : 19.0°C / 66.2°F
CPU Temperature : 42.5°C / 108.5°F
Power / Aux Temperature : 42.5°C / 108.5°F

Cooling Device(s)
Auto Fan Speed Control : No
Power / Aux Fan Speed : 2637rpm

Voltage Sensor(s)
CPU Voltage : 1.63V
Aux Voltage : 1.60V
+3.3V Voltage : 2.77V
+5V Voltage : 5.03V
+12V Voltage : 11.73V
-12V Voltage : -6.93V
-5V Voltage : -5.20V
Standby Voltage : 5.09V
Battery Voltage : 3.09V

AGP Bus(es) on Hub 1
Version : 3.00
Speed : 8x
Fast-Writes Enabled : Yes
Isochronous Mode Enabled : No
Addressing Enabled : 32-bit
Aperture Size : 256MB

PCI Bus(es) on Hub 1
Version : 2.20
Number of Bridges : 2
PCI Bus 0 : PCI (1/1x PCIClk)
PCI Bus 1 : PCI (1/1x PCIClk)

LPC Hub Controller 1
Model : Epox Computer Co Ltd nForce2 ISA Bridge

USB Controller 1
Model : Epox Computer Co Ltd nForce2 OHCI USB Controller
Version : 1.00
Interface : OHCI
Channels : 3
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 2
Model : Epox Computer Co Ltd nForce2 OHCI USB Controller
Version : 1.00
Interface : OHCI
Channels : 3
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 3
Model : Epox Computer Co Ltd nForce2 EHCI USB 2.0 Controller
Version : 2.00
Specification : 1.00
Interface : EHCI
Channels : 6
Companion Controllers : 2
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps) High (480Mbps)
Addressing Support : 32-bit
Legacy Emulation Enabled : No

System SMBus Controller 1
Model : nVidia MCP2/3/4 B0 SMBus
Version : 0A.02
Advanced TCO Mode Enabled : No
Slave Device Enabled : No
PEC Support : No

System SMBus Controller 2
Model : nVidia MCP2/3/4 B1 SMBus
Version : 0A.02
Advanced TCO Mode Enabled : No
Slave Device Enabled : No
PEC Support : No

Expansion Slot(s)
PCI0 (1h) : PCI 32-bit +5V PME Full-Length Available (Epox Computer Co
Ltd nForce2 ISA Bridge)
PCI1 (2h) : PCI 32-bit +5V PME Full-Length Used (Epox Computer Co Ltd
nForce2 OHCI USB Controller)
PCI2 (3h) : PCI 32-bit +5V PME Full-Length Used
PCI3 (4h) : PCI 32-bit +5V PME Full-Length Available
PCI4 (5h) : PCI 32-bit +5V PME Full-Length Available
AGP : AGP 32-bit +5V Full-Length Used

Port Connector
PRIMARY IDE : None - ATA / None
SECONDARY IDE : None - ATA / None
FDD : 8251 FIFO - Floppy Disk / None
COM1 : Serial Port 16450 - 9 Pin Dual Inline / DB-9 pin male
COM2 : Serial Port 16450 - 9 Pin Dual Inline / DB-9 pin male
LPT1 : Parallel Port ECP/EPP - DB-25 pin female / DB-25 pin female
Keyboard : Keyboard - PS/2 / PS/2
PS/2 Mouse : Mouse - PS/2 / PS/2
USB : USB - None / None

Performance Tips
Notice 224 : SMBIOS/DMI information may be inaccurate.
Tip 2511 : Some memory slots are free so the memory can be easily upgraded.
Tip 2 : Double-click tip or press Enter while a tip is selected for more
information about the tip.
Received on Mon Mar 7 23:00:27 2005